Rule 17A General Purpose Centrifugal Pump 3800 GPH 12V

Designed for use as a washdown pump and/or Livewell tank pump. It delivers lots of water but at low pressure.

Rule 33ALA High Water Bilge Alarm

Rule 35FA Rule-A-Matic Float Switch Fused

It includes a fuse holder to allow for installing the correct size of AGC fuse required for the pump.

Rule 37A Automatic SuperSwitch

Rule 40A Rule-A-Matic Plus Float Switch

Designed for pumps drawing up to 20 Amps. The 40A Switch is not fused but can be combined with a fused Switch Panel like the Rule 41.

Rule 40FA Rule-A-Matic Plus with In-Line Fuse Holder

Includes fuse holder and is for use with Standard bilge pumps drawing up to 20 Amps. For use with 12V, 24V or 32V DC electrical systems.

Rule 41 3-Way Bilge Switch Panel Lighted

Toggle has three positions (Automatic, Off, or Manual) and has a "fail-safe" spring return to "Off" from the "Manual" position.

Rule 45 3-Way Panel Bilge Switch

Controls any pump equipped with an automatic float switch.

Rule 66 Side Mounting Bracket for Bilge Pump

Permits the round Rule 360, 500, 1100 pump models to be side mounted to a vertical stringer, a bulkhead or a transom.

Rule Bilge Pump Strainer Base

Rule High Speed Inflator/Deflator

The Rule High Speed Inflator/Deflator inflates a typical 4-man dinghy or a 120" X 72" X 22" family inflatable pool under 2 minutes. Adjustable nozzles have been included for most inflatables and valve types.

Rule DB412 Dry Bilge Pump 4.0 GPM 12 Volt

Pumps down to 1/8" (3 mm) so you can have a dry bilge, and a dry bilge is a clean, odourless bilge. This new Rule bilge pump gets the last of the water out.

Rule 20DA 800GPH Bilge Pump 12V

Has a high flow-optimized impeller to provide greater flow at the same amperage as previous generations. Built-in Thermal Cut-Off provides added protection for the pump and vessel. A built-in check valve reduces the amount of water left over in the bilge, reducing odor and helps keep your bilge cleaner.

Rule 98B-24 Shower Drain 800 GPH 3-Port 24V

24V Shower drain with automatic pumping without external floats or switches to tangle, stick or fail; Heavy duty construction; Completely submersible.

Rule 24DA Bilge Pump 360 GPH

Rule 25DA 500 GPH Bilge Pump

Exclusive Rule Moisture Tight Seals; Compact, Efficient, Maintenance Free; Positive Snap Lock Strainer Base; Totally Submersible

Rule 20A Bilge Pump 1000 GPH

Rule 27DA Bilge Pump 1100 GPH 12V

Exclusive Rule moisture tight seals. Compact, efficient, maintenance-free. Positive snap-lock strainer base.

Rule 02 Bilge Pump 1500 GPH

Choose from 12V DC or 24V DC. A totally submersible, silent running, vibration-free, ignition-protected performer.

Rule 10 Bilge Pump 2000 GPH 12V

No burn-out when running dry; Stainless Steel Shaft.; Engineered to commercial standards. Pumps 2000 GPH.

Rule 56D Bilge Pump 4000 GPH 12V DC

Large 2" discharge outlet with an open flow rate of 4,000 GPH.

Rule 12 2000 GPH 24 Volt Bilge Pump

24 Volt model of the 2000 GPH Cartridge Series of bilge pumps offers traditional operation activated by a float or panel switch.

Rule RM500B Rule-Mate Automatic 500 GPH Bilge Pump

The new eco-friendly Rule Mate pump is a fully automated bilge pump featuring solid state water sensing technology to eliminate a separate float switch.

Rule RM800B Rule-Mate Automatic 800 GPH Bilge Pump

Features a pump and a non-contact, mercury free float switch in a single, compact housing. When the float rises, the pump begins to turn on.

Rule RM1100B Rule-Mate Automatic 1100 GPH Bilge Pump

Solid state water sensing technology eliminates the need for a separate float switch. Turns on when water level reaches approximately 2-1/2" and shuts off at 5/8".

Rule LP900S LoPro Automatic Bilge Pump 900 GPH

Fully automatic, low profile pump designed for tight spaces, only 2 1/4" tall and 9 1/4" long. Discharge body swivels up to 180 degrees for ease of installation.

Rule LP900D LoPro Non-Automatic Bilge Pump 900 GPH

Only 58 mm high, the entire discharge body swivels up to 180 degrees for ease of installation, and the hose can also swivel 360 degrees for better routing. This non-automatic model requires a Float and, or a Panel switch.

Rule RM1500A Rule-Mate 1500 GPH Bilge Pump

Features a pump and a non-contact, mercury free float switch in a single, compact housing. When the float rises, the pump begins to turn on.

Rule RM2000A Rule-Mate 2000 GPH Bilge Pump

When water enters the bilge and reaches 2" (50 mm) in height, solid-state water sensing technology turns the pump on.

Rule 25SA Fully Automatic Bilge Pump 500 GPH

Automatic pumping without external floats or switches to tangle, stick or fail; Heavy duty construction; Completely submersible.

Rule 27SA Fully Automatic Bilge Pump 1100 GPH

Now includes "back flow preventer" and comes with 2 hose barb connections 1" and 1-1/8"

Rule 53S Fully Automatic Bilge Pump 2000 GPH

Float switches are not required. The pump will turn on every 2-1/2 minutes for about one second to sense for water.

Rule 14A 3700 GPH Bilge Pump 12V

This non-automatic 12V Rule 14A model is UL listed with 6' wire leads.

Rule 16A 3700 GPH Bilge Pump 24V

For use with 24V DC systems. Heavy-duty construction for commercial and pleasure use; known for trouble-free operation and reliability. 1-1/2" (38 mm) discharge outlet.

Rule 98B Shower Drain 800 GPH with Multi-Port Inlet 12V

Automatic pumping without external floats or switches to tangle, stick or fail. Heavy-duty construction and completely submersible.